- Видео 50
- Просмотров 3 742 283
Dave Osland
Добавлен 19 сен 2013
Here's a channel where Dave shares some of his "how to's". Check back for some welding tutorial's next.
Making Bread and Butter Pickles!!
FreckleBack Farms shares it's recipe for making it's popular
Bread and Butter Pickles!
Bread and Butter Pickles!
Просмотров: 320
Видео
Honda Quad Carb Improvement!
Просмотров 1372 месяца назад
Dave re-jets a Honda TRX250 quad carburetor for a huge perfomance improvement! An hours work and $3 part!
$4 Toilet Fix???!!!
Просмотров 1,1 тыс.7 месяцев назад
Dave shares how to fix a common toilet problem for "weak" flushes!!
Flail Mower Hammer Blade Sharpening
Просмотров 4,9 тыс.Год назад
Dave shows how he sharpens Hammer-Head blades on a WoodMaxx Flail Mower
Ornamental Iron Railing Fabrication
Просмотров 367Год назад
Dave fabricates an Ornamental Iron Railing
Honda 680 Rincon Oil and Filter Change
Просмотров 11 тыс.Год назад
A quick, 3 minute video on changing the oil and filter on a 2016 Honda Rincon 680 ATV1
Ornamental Iron Gate Fabrication
Просмотров 1,9 тыс.Год назад
Dave takes us through the tools and techniques to build an ornamental iron gate.
Makin' Bread and Butter Pickles!
Просмотров 5072 года назад
Carrie shares FreckleBack Farm's recipe and know-how for her famous Bread and Butter Pickles!
ATV Hitch for Little Quads!
Просмотров 12 тыс.2 года назад
Not finding one to buy, Dave builds a hitch for a small atv, a Honda TRx90!
Making Apricot Jam!!!
Просмотров 11 тыс.2 года назад
Carrie, at FreckleBack Farms, walks us throught the fun, easy process of making (and canning), jam, from fresh Apricots!
Chevy Truck Front Bumper Build
Просмотров 12 тыс.2 года назад
Dave builds a custom front bumper for a 2003 Chevy 2500, from start to finish.
Truck Bumper Build!
Просмотров 4 тыс.2 года назад
Dave fabricates a rear bumper for a 2003 Chevy truck
Flail Mower Review
Просмотров 27 тыс.2 года назад
Dave talks the WoodMaxx Flail Mower, sharpening the blades and welding careers!
Building Boat Guide On's
Просмотров 3,6 тыс.3 года назад
Dave goes thru the process of building Heavy Duty boat guide-ons....
Concrete Stem Wall to Slab Connection
Просмотров 26 тыс.4 года назад
Concrete Stem Wall to Slab Connection
Welding Test Plate- Back Up Bar Removal
Просмотров 18 тыс.5 лет назад
Welding Test Plate- Back Up Bar Removal
Residential Construction- Start to Finish!
Просмотров 204 тыс.6 лет назад
Residential Construction- Start to Finish!
Building a Reclaimed Lumber and Steel Table
Просмотров 6076 лет назад
Building a Reclaimed Lumber and Steel Table
Ornamental Iron at Cabrillo College
Просмотров 1,1 тыс.6 лет назад
Ornamental Iron at Cabrillo College
how do you plan to get into the crawl space?
Good question! At the rear of the foundation, in a taller area of the forms, a "block out" area in the forms, 24" wide x 18" high, is made, where the concrete is not allowed to fill, providing an access portal. Without that, a access hole would have to be formed in the subfloor framing.- Dave
Nice work! I see why you built it this way. Makes sense...
Thanks! The kids love using the little quad and trailer to help with work on the property!
ขอพากเปันพาสาไทย
I like this brand. I want a flail mower. If it could mow ditch banks I would buy it. The FM 96H ditch bank mower? A FM 108 H ditch bank mower would be even better for my orchard. My bush hog cuts 3 inch saplings all day long and has been doing it since 1999.
Howse 7 foot heavy duty rotary cutter with a 100 hp gearbox.
I have a hydraulic adjustment to pitch an angle on my unit, so as to put a 15 degree pitch on the mower, but nothing that you would get on a mower specifically designed for ditches. This unit will grind 2" brush. Dave
Beautiful work
Thanks Jose!
Not actually watching you lay it out, review if you're using inside or outside diameters of the pipe being laid out. An excellent resource on pipe and sheetmetal layout is "Sheet Metal" by Leo Meyer- Dave
I don't know what I'm missing but I'm following your tutorial to the T using smaller pipes and in the end it comes out dramatically wrong every time no matter how many times i try it, even with different diameter pipes.... Anyone please help...
How much sugar do you use in this recipe?
Do u know where I can get the recipe paper they had in the sure jell box yr. ago? I can’t find mine and they do not put in boxes anymore. Thx for video.
Terrible layout...never should've had that little sliver along the wall. The tile along the tub should've been a little smaller, allowing the ones along the wall to be wider.
They had us grind it lol this looks so much easier
That's a lot of grinding! You still need to grind, but this reduces time. Dave
What elevation are you? Do you need to adjust time for elevation?
We're close to sea level. Just add a few minutes for high elevation- Have fun and enjoy!
Just flip the blade around so the unused side engages. When it's dull, you can sharpen both sides at the same time you take 'em off. I didn't see any jackstands under that mower you were UNDER!
These blades only have 1 cutting edge- "can't be flipped around" No jackstand- A bolt is inserted in the side holes, preventing the unit to drop... Dave
You may not be a "polished video guy" but this one is spot on - straightforward, nicely shot, clear, and your commentary has lots of useful points in it. Thanks ! Sometimes Simple is Best. Richard
Thanks Richard! I get faster each time I have to sharpen the buggers! Dave
NM plate ! I would not claim California ether lol. NM born and bread
Great style like the bumper and protection thought process
Thanks! Dave
Why does it look like you're giving it a flat grind instead of angled?
I think because the actual angle is not very narrow ? so it's not sharp like a knife with a very tapered blade, it's a-bit-less-than-flat but with a well-defined edge. That would make the resulting edge a lot stronger than a fine taper, and given what flail mowers go through, strength is very important !
I love it but can you do it on a Coleman on a Coleman Kids four wheeler please
Hi- With some basic fabrication skills, I bet any little quad can be set up to pull a littles trailer- Dave
I wouldnt rejet it from the Honda factory unless you modify intake or exhaust. Older carbs id run through a ultrasonic cleaner to bring it back to oem. vs jetting it.
Having owned dozens of modified dirt bikes and quads, the minor change from a #38 to 40 is a small change, not worthy of any other mods. The #38 jet was clean. The#40 made all the difference in the world. Unfortunately, to meet emmisions, the factory had to set up the quad super lean.
Excellent job brother. Thanks for wrench sizes and component locations. God bless you and yours.
Thank You! Just posted a qued carb rejet....
This video is an incorrect and an inaccurate technique. The true lengths should be transferred to the right hand side by taking them perpendicular to the centre line.
Super very good 👍
Thanks for the visit
Dave, this is super neat! Looking for the same for my daughter's 2016 trx90x... no chance youd make one and ship it? Happy to pay for it, would save me a freat deal of time. I live in MA.
I'd make one for you if you lived near by..(Ca.) No one you know can fab one up for you?? You could cut the pieces, drill and use fasteners to assemble.. Thanks you the interest! Our youngsters love being part of the farm work pulling things around!- Dave
Would a flail mower be effective in clearing/tilling weeds in a sandy horse arena? The sand is usually around 3-4” deep.
No- I would use something like a "Drag King" or an "arena drag" to dress the field. Dave
Hey I do sheet metal fabrication for insulation on piping would this method work ??
Where are the foundation vents?
Good question! The vents will be cut in the subfloor frame rim board. See the subfloor frame video- ruclips.net/video/4xMSep0uiRs/видео.html Dave
Quick easy straight to the point, no stupid music.. great video
I couldn't find any rap that went with an oil change.... Dave
What is the make of the compass you are using and how long is it ? Thank you.
Great job. Better than any store bought. Inspired me. I'm gonna make one for my 2014 Z71. Factory one is crap, way too thin.
Let us know how it turns out! Dave
Awesome thanks for info ...
3" into 4". Not the other way around.
Super good job..
hello, after you put the mold in the kiln - where does the wax melt off to?
Excuse the late reply. Good question! The high temp, 1300 degrees f., basically vaporizes the wax and must be done in a ventilated setting, as in a open shop.
Makes me think the owner is going to keep his car collection down there. Two large overhead bays, no windows, high ceiling for 4-post car lift. Nice that the floor is going to drop onto the stem wall on that pour.
Hey mate, would you be able to do a video on a lobster back ? If your still doing these videos
In the water bath process is the water over the top of the jar and lids?
Can you share the link of the parts . Thank you .
One more
what's the thickness of them plates? 5mm?
3/16", 4.7mm
What hp Kubota are you running? Thinking about getting same unit for my L3940
A L35, 2001 model, (33 hp), 27hp at the PTO
Thank you
Really helpful. Thank you
Glad you found it helpful! Dave
Just in case you didn't know, WoodMaxx makes their mowers in communist China.
A great help, much appreciated 👍
Do you have any drawings of projection of an L joint at 45°
6 people in the house how do I let it set for more than a hour
That's a tough one if there's no other toilet! There are faster acting solutions/chemicals that are used, but their use is generally frowned upon... Dave
Is this the same for joining 2 pipes that are the same diameter?
Yes, but with pipe of the same diameter, templates and be commonly bought for smaller diameter pipe, if so desired... The above process is excellent for pipe coneections of different sizes! Dave
Thanks, I learnt it years ago while I was an apprentice and have forgotten how to do it for 90 degree joins. So if both pipes are 150 diameter it’s the same menthod as you’ve shown, do I still use the ID or the OD measurement
A... 150 diameter?@@callumtonks5
@@daveosland3199 150mm diameter for example
I use the I.D.@@callumtonks5
Interesting
Yep, an easy fix , if the sediment is an issue... Dave
Thigh Catcher
Brilliant piece of work
OK, love the video and the technique, and obviously it works. But it looks to me, for the layout of the 16 segments on the long line, at 4:26, you measured not arcs, but chords which would define an inscribed polygon, which would have a shorter circumference than the circle you are working with. And yet the cut out template fits the pipe, and I can’t see why. I don’t think the 1/32 inch gap in the conclusion explains anything. Dave? Anyone?